hidden hit counter


HOME

 

FORUM ARCHIVE

 

CAD PLANS

 

TECH FEATURES

 

ADMIN 1

 

ADMIN 2



Top The TRMA Discussion Forum topic #49209
View in linear mode

Subject: "RE: Vertical sliding Watertight Door system" Previous topic | Next topic
SteveFuryTue Feb-21-17 05:25 AM
Member since Feb 20th 2017
13 posts
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#54684, "RE: Vertical sliding Watertight Door system"
In response to In response to 2
Tue Feb-21-17 05:28 AMby SteveFury

          

>TTSM pg.113 is the best picture of H&W's WT door mechanism.
>That's the picture with a man in it. The description is
>already very good.
>
>Door movement:
>Let's call the shaft with the gear above the center of the
>door the main shaft.
>That gear is fixed on the shaft. The shaft can move left-right
>by a small amount.
>The worm gear at the side of the door frame is free to spin on
>the main shaft.
>That gear would have a bearing surface on its left side.
>The main shaft has a head like a nail to the right of the worm
>gear.
>A friction material (B) would be placed between the main shaft
>head and the worm gear.
>The weight arm (C) pivots on a rod in the casting next to the
>head of the main shaft.
>Beneath that pivot rod is a bolt tip that pushes on the main
>shaft head pressing it against the friction material and the
>worm gear.
>
>So when the weight presses down, the main shaft is clamped to
>and obeys the worm gear, stopping or moving with it.
>When the weight is up, the main shaft is free to let the door
>fall by gravity.
>
>The friction area could actually be built of several layers
>like a multi disk automotive clutch.
>Maybe the main shaft doesn't slide sideways, the head could be
>a splined casting that slides on it.
>As the Stone hydraulic door system became more popular there
>is probably not much in the period texts. A patent search
>might lead to better details.
>
>In the final assembly the two gears and the friction area are
>covered.
>
>Control:
>A small vertical rod (E) runs down from the large magnet box
> A) at the top to the float at the bottom.
>The magnet is wired by thin conduit mounted on posts above it
> pg.112 left). The magnet is energized to lift the control rod
>and thus the weight. Nowadays that would not be considered
>fail safe.
>A hand release lever (D) on the bulkhead can also lift the
>control rod.
>At the bottom the float sits in an enclosure. When the float
>lifts it works through a lever on a bracket to lift the
>control rod. The lever and bracket show in this picture.
>
>For opening the door the vertical shaft (G) through the worm
>gear can be cranked by a bevel gear (F) at the bottom. The L
>shaped gear handle is hanging on the bulkhead. The shaft can
>also be cranked from an upper deck. These routes can also be
>used for slow or remote closing of the door.
>
>Cataracts* (old name for a flow slowing passageway):
>The two hydraulic style cylinders above the door have a closed
>fluid circuit. The small pipes at the side only allow fluid to
>move from beneath the pistons to above them at a rate slow
>enough to give a controlled descent of the door. When the
>pistons pass the extra pipe connections 2/3's of the way down
>more fluid can pass into the upper part of the cylinder and
>the descent rate becomes quick enough to let the door slam
>home.
>
>Bill
>
>*I think cataract is an alternative to the word rapids as in
>river rapids. Much as we think of them as being fast water the
>rocky, restrictive bottom makes them slower than a smooth
>bottomed passageway making the same descent. Hence the period
>use of the word here for a slowing mechanism. In my time the
>word dashpot was used for this sort of mechanism.


If I understand correctly, the release mechanism which consists of the solenoid magnet, the manual release lever and float did not latch to allow the door to complete its slow decent?
I mean to say... The current switched on at the bridge had to keep the magnet on at least until the door dropped? It seems a better way would have been that a single pulse to the magnet would trip the mechanism to drop the door.

It looks like the manual lever also needed to be held upward for the duration of the door travel until it slammed shut. If the manual release handle was let go half way down then the door would stop half way down.
Right?

Steve Fury
from Atlanta,GA USA

  

Alert | IP Printer-friendly copy | Reply | Reply with quote

Vertical sliding Watertight Door system [View all] , Axim de Ryme, Thu May-23-13 04:22 PM
  RE: Vertical sliding Watertight Door system, b-rad, Feb 17th 2017, #1
RE: Vertical sliding Watertight Door system, Bill West, Feb 18th 2017, #2
      RE: Vertical sliding Watertight Door system, Ralph Currell, Feb 18th 2017, #3
      RE: Vertical sliding Watertight Door system, Bill West, Feb 18th 2017, #4
      RE: Vertical sliding Watertight Door system, Ralph Currell, Feb 19th 2017, #5
      RE: Vertical sliding Watertight Door system, Scott Andrews, Feb 19th 2017, #6
           RE: Vertical sliding Watertight Door system, Ralph Currell, Feb 20th 2017, #7
                RE: Vertical sliding Watertight Door system, Axim de Ryme, Feb 20th 2017, #8
                RE: Vertical sliding Watertight Door system, Ralph Currell, Feb 20th 2017, #10
                RE: Vertical sliding Watertight Door system, Scott Andrews, Feb 20th 2017, #9
                     RE: Vertical sliding Watertight Door system, Ralph Currell, Feb 20th 2017, #11
                          RE: Vertical sliding Watertight Door system, Bill West, Feb 21st 2017, #14
      RE: Vertical sliding Watertight Door system, SteveFury, Feb 21st 2017 #12
           RE: Vertical sliding Watertight Door system, Bill West, Feb 21st 2017, #13
                RE: Vertical sliding Watertight Door system, Scott Andrews, Feb 21st 2017, #15
                     RE: Vertical sliding Watertight Door system, Ralph Currell, Feb 23rd 2017, #16
                          RE: Vertical sliding Watertight Door system, b-rad, Mar 07th 2017, #17
                               RE: Vertical sliding Watertight Door system, Ralph Currell, Mar 08th 2017, #18

Top The TRMA Discussion Forum topic #49209 Previous topic | Next topic


Titanic artwork at top of page is owned and copyright of Stuart Williamson and is used with permission.